Introduction

Love for a bicycle begins with the first kilometers - with a sense of freedom, speed and complete control over the route. But this novel with a two -haired friend requires responsibility. Even the most reliable bike begins to give signs over time: light creaks, uncertain turns, strange vibrations. To ignore them means risking not only comfort, but also safety.

Author's blog CyclitroNiona Dedicated to a reasonable and conscious cycling, is shared by an important selection of symptoms, which should pay attention to each owner of the bicycle. A technical inspection is not a formality, but the basis of reliability on the road. Especially if you want to use the maximum capabilities of your bicycle and system plus , which includes wider tires, increased lifting capacity and stability on the highway.

Main part: 10 signs that the bicycle needs inspection

1. The bicycle "noise" on the go
If your bike began to creak, click or tremble during pedaling, these are not just annoying little things. Sounds can indicate problems with a carriage, chain, bushings or pedals. Even a slight tapping with regular driving can lead to a breakdown of components, especially with increased loads typical of models with a platform plus .

2. The chain jumps when switching
Inaccuracy in switching the gears, response delay or a sudden breakdown of the chain is an occasion to check the transmission. This may be the result of the wear of the stars, the weak tension of the cable or the contaminated switch. Transmission setting is the basis of smooth and safe pedaling, especially in conditions of crossed terrain.

3. The braking distance has increased
If you notice that the bicycle began to slow down worse, especially on a wet surface, it is worth checking the condition of the pads, disks or rims. Also, the cause may be pollution or wear of the brake system. Working brakes are a question of not only technology, but also life, especially on descents and in urban traffic.

4. Wheels do not keep a direction
Side vibrations, play or instability when moving indicate the need to check bushings and knitting needles. Incorrect stretch or weakened components affect controllability and can lead to deformation of the rim. For bicycles with wide type tires plus This is especially critical, because with a high load, the slightest deformation intensifies.

5. Depreciation has become ineffective
If the fork does not “work out” unevenness, and the bike seems “tough” on the road, perhaps shock absorbers require adjustment or complete bulkhead. This is important not only for comfort, but also for control at speed. An off -road bicycle working in the system is especially sensitive to this plus .

6. Luft appeared in a steering column or carriage
Free steering or a shat of pedals is not a trifle. This is a direct indication that the key connections are crashed or worn out. In such conditions, the risk of sudden loss of control over movement increases, especially on bends or with sharp braking.

7. Reduces of tire pressure
If the tires require pumping too often, the problem may not be in the nipple, but in microcracks on the chamber or sidewall of the tire. It is also worth checking the landing of the tire on the rim. When using plus -The cover with a large volume of air, this becomes especially noticeable, since even a small loss of pressure affects control.

8. Leather and winding on the steering wheel are worn out
Loss of adhesion to the steering wheel, flux cracks or slippery surface is a signal to replacement. Contact zones directly affect the sense of safety while driving. It is worth remembering that when falling, the steering wheel becomes a support point, and its quality can play a key role.

9. Damage to the elements of a frame or fork
A small dent or crack at the junction of the pipes can develop into a breakdown. Especially if you use a bicycle for long -term trips, Turin or rough terrain. In such cases, it is important to regularly inspect welds and areas of increased load.

10. You do not remember when you last served a bicycle
Even if everything seems in order, the lack of prevention is an occasion to look into the workshop. A bicycle, which is regularly subjected to loads, should undergo inspection at least once a season. Professional service will provide cleaning, setting up, lubricating and replacing worn components, including updating the elements suitable for the system plus , if your driving style provides this.

Conclusion

The bicycle, like any technical tool, requires regular care and attention. Signs of wear are not immediately manifested, but the accumulative effect can lead to a breakdown at the most inopportune moment. Author's blog CyclitroNiona Reminded: inspection is an investment in comfort, safety and pleasure from every trip.

Do not wait until the malfunction becomes obvious. Listen to the signals that your bike gives, and give him a chance to serve you longer. And if you ride actively, including on a bicycle with the system plus Timely maintenance is your best ally in any conditions.